Sanitizer

Pool Salt Level: What PPM Should It Be?

What should a pool's salt level be? The ppm range from salt cell manuals, what low and high readings do, how much salt to add and how to lower it.

Jump to the calculator

On this page
  1. Salt level chart from the manuals
  2. How to test salt
  3. If your salt level is too low
  4. If your salt level is too high
  5. Why the level keeps dropping
  6. Common mistakes
  7. Track it in Pool Calc
  8. Sources
  9. Safety

The quick answer: the right pool salt level is the range in your salt cell's manual. Two common residential manuals list 2,700 to 3,400 ppm, with 3,200 optimal, and 3,000 to 3,500 ppm. Going from 2,700 to 3,200 ppm in 10,000 gallons takes about 42 lb (19 kg) of 99% pool salt. Check your model before you add any. Follow the product label.

The calculator below works out the amount from your pool's volume, your reading and your cell's target.

Pool salt calculator

gal

Not sure? Work out your pool volume.

ppm

Enter 0 for a first fill.

ppm

Use the number in your cell’s manual.

%

Add

88lb

of Pool salt (sodium chloride 99%)

1,410 oz40 kg

Raises salt from 2,500 ppm to 3,200 ppm in 15,000 gal. That is about 2.2 bags of 40 lb.

  • Brush the salt around until it dissolves, and keep the salt cell off for 24 hours.
  • If you are unsure of your volume, add about 80% first, circulate for 24 hours and retest.

Check the product label. Strengths vary by brand, so enter the % printed on yours. Add one chemical at a time, into the water, and never mix chemicals.

Save this test and get reminded when it is time to retest.

Download on the App Store

Salt level chart from the manuals

These are the makers' own numbers for the models named. Your manual decides for your cell.

Manual Recommended Too low Too high
Hayward AquaRite (AQR models) 2,700 to 3,400 ppm, 3,200 optimal Below 2,700 ppm: warning light, low efficiency Starts to taste salty at about 3,500 to 4,000 ppm; can shut down
Pentair IntelliChlor IC15 3,000 to 3,500 ppm Below 2,600 ppm: unit turns off Above 4,500 ppm: may cause corrosion
Pentair commercial IntelliChlor 3,600 to 4,500 ppm Below 3,300 ppm: reduced efficiency; below 2,600 ppm: off Above 4,500 ppm: may cause corrosion

The commercial row shows why a number from a neighbour's pool or another manual may not fit yours. If you can't find your manual, look up the model on the maker's website.

How to test salt

Don't rely on the cell's display alone. Pentair's IC15 manual says its salt sensor reads within plus or minus 500 ppm, and it asks you to confirm the level by a separate reliable test. Hayward advises having low salt professionally checked before adding a large amount.

Test again 24 hours after adding salt. Both manuals allow about that long for the salt to dissolve and spread through the water, and Hayward's display can take 24 hours to catch up.

If your salt level is too low

  1. Confirm it with a second test.
  2. Work out the amount with the salt calculator, or look up your pool size on the how much salt page. As a guide, a first fill to 3,200 ppm in 10,000 gallons takes about 269 lb (122 kg).
  3. Use the right salt. The manuals call for high-purity sodium chloride: above 99% in Hayward's, at least 99.8% in Pentair's. Both warn against salt with additives, and Hayward names iodized salt, rock salt and anti-caking additives. Follow the product label.
  4. Add it to the pool with the pump running. Pentair says to pour slowly around the perimeter, and not through the skimmer. Hayward says to brush the salt around so it doesn't sit on the bottom.
  5. Circulate for 24 hours, then retest. Log the reading in Pool Calc for iPhone, so the next test has something to compare against.

While the salt is low, the cell makes less chlorine. Test free chlorine as well, and see the FC/CYA chart for the level your pool needs.

New plaster: wait before adding salt. Hayward says 10 to 14 days and Pentair says at least one month after construction. Follow your own manual and your builder.

If your salt level is too high

Salt doesn't leave on its own, because evaporation takes only the water. The fix is to drain part of the pool and refill with fresh water, as Hayward's manual says. The drain and refill calculator shows how much to replace. Retest once the water has mixed, and rebalance if you replaced a lot, since a partial drain also lowers stabilizer, alkalinity and calcium. Before you drain, check your pool maker's or builder's instructions.

Why the level keeps dropping

Salt isn't used up in normal running. Hayward's manual says chlorine reverts to salt after it does its work, and that salt is lost mainly through splashing, backwashing, or draining because of rain. It also says salt isn't lost to evaporation.

So a drop usually traces back to water leaving the pool. If you have lost no water, test again by a second method before adding salt.

Cold water matters too. Hayward's unit stops making chlorine below 50°F, so a cold pool with no chlorine output isn't always a salt problem. How much liquid chlorine to add covers topping up by hand.

Common mistakes

  • Adding salt because the light came on, with no second test. Salt is slow to remove.
  • Using another pool's number. Models differ, so check your own manual.
  • Adding it all at once when the volume is a guess. Add part of it, circulate for 24 hours, and retest. Our gallons guide helps you pin the volume down.
  • Ignoring chlorine while fixing salt. Test both. Pool Calc keeps both readings in your history.

Track it in Pool Calc

Pool Calc logs salt, works out how much to add for your pool's volume and your cell's target, and reminds you when to retest. Get Pool Calc for iPhone and log your next test.

Sources

Safety

  • Keep chemicals out of reach of children and pets, and keep them out of the water until it is back in range.
  • Never mix chemicals. Never add acid and chlorine together: mixing them releases toxic chlorine gas.
  • Add chemicals to water, never water to chemicals.
  • Store chemicals sealed, cool and dry, apart from each other.
  • Read and follow the product label. It always comes first.

Questions

What should the salt level be in a pool?

Use the range in your salt cell's manual. Two common residential manuals give 2,700 to 3,400 ppm (3,200 optimal) and 3,000 to 3,500 ppm, so about 3,000 to 3,400 ppm sits inside both. A different model can list a different range.

What happens if pool salt is too low?

The cell makes less chlorine and eventually shuts off. One manual says this starts below 2,700 ppm, and another says the unit turns off below 2,600 ppm. Test free chlorine too, because the pool may be short of chlorine by then.

What happens if pool salt is too high?

Water can start to taste salty at about 3,500 to 4,000 ppm, and one manual warns of corrosion above 4,500 ppm. The cell may also shut down. The fix is to drain part of the water and refill with fresh water.

Why does my pool salt level keep dropping?

Salt is lost with the water that leaves the pool: splash-out, backwashing and draining after rain. It doesn't evaporate and isn't used up by making chlorine. A steady drop with no water loss is worth a second test, since the cell's reading can be off.

How much salt raises a pool's salt level?

Going from 2,700 to 3,200 ppm in 10,000 gallons takes about 42 lb (19 kg) of 99% pool salt. Follow the product label and your cell's manual, and add less than the sum if you are unsure of your volume.