Problems and fixes

Cloudy Pool After Shock: Why It Happens and How to Clear It

Cloudy pool after shock? Find out if it's dead algae, a SLAM that isn't finished, calcium from cal-hypo or the filter, and how to clear it safely.

Jump to the calculator

On this page
  1. First: test before you add anything else
  2. Reason 1: the filter is still clearing dead algae
  3. Reason 2: the shock wasn't held long enough
  4. Reason 3: cal-hypo and calcium carbonate (milky white water)
  5. Reason 4: the filter isn't keeping up
  6. Clarifier or floc after shocking?
  7. When can you swim?
  8. A quick diagnostic table
  9. Common mistakes
  10. Track it in Pool Calc
  11. Sources
  12. Safety

The quick answer: a cloudy pool after shock usually means the filter is still removing what the chlorine killed, and that can take a week or more after a full algae treatment. If the water isn't getting a little clearer each day, check three things: is the shock level being held for your stabilizer (CYA), was the shock cal-hypo in water with high alkalinity and pH, and is the filter keeping up. Keep everyone out until you can see the main drain, and follow the product label for every chemical you add.

The shock calculator below works out the shock level for your CYA and how much of your product it takes.

Shock (SLAM) calculator

gal

Not sure? Work out your pool volume.

%
ppm

The shock level is 40% of CYA, never below 10 ppm.

ppm

Add

2.1gal

of Liquid chlorine 10%

269 fl oz7.9 L

Raises free chlorine from 2 ppm to the shock level of 16 ppm (40% of CYA 40) in 15,000 gal.

  • Side effects: Salt +23 ppm.
  • Pour it slowly in front of a return jet with the pump running.
  • Hold free chlorine at 16 ppm: retest and top up at least morning, midday and evening.
  • You are done when combined chlorine is 0.5 ppm or less, the overnight chlorine loss is 1 ppm or less, and the water is clear.
  • No swimming during the SLAM. Swim when free chlorine is back within your normal range and at or below the re-entry level on your chlorine label (many labels say 4 ppm). Never swim during a SLAM or with free chlorine above 10 ppm. Your product label always comes first.

Check the product label. Strengths vary by brand, so enter the % printed on yours. Add one chemical at a time, into the water, and never mix chemicals.

Save this test and get reminded when it is time to retest.

Download on the App Store

First: test before you add anything else

Cloudy water after a shock has a cause you can measure. Test:

  • Free chlorine (FC) and CYA. The shock level depends on CYA: it is 40% of CYA, for example 20 ppm at 50 ppm CYA and 32 ppm at 80 ppm CYA. If FC is already below that, the job isn't finished.
  • Combined chlorine (CC). Total chlorine minus free chlorine. A reading above 0.5 ppm means there is still something for chlorine to break down.
  • pH, total alkalinity and calcium hardness. These tell you whether the haze could be calcium carbonate.
  • Filter pressure. Compare it with the reading when the filter was clean.

Write every result down. Logging them in Pool Calc for iPhone keeps the readings side by side, so you can see whether chlorine is holding from one test to the next.

Reason 1: the filter is still clearing dead algae

This is the most common reason and the most normal one. Chlorine kills algae and breaks down contaminants, but the remains stay in the water until the filter catches them. TroubleFreePool's Pool School says the water should look a little better each day, that it can take the filter a week or more to clear it completely, and that sand filters are the slowest, with cartridge filters in between.

What to do:

  1. Run the pump around the clock until the water is clear.
  2. Brush and vacuum the whole pool daily, including inside skimmers, behind ladders and under the main drain cover, as Pool School recommends.
  3. Backwash or clean the filter when its pressure rises about 25% above the clean reading.
  4. Watch for daily progress. No improvement at all is a sign to look at the filter (reason 4).

Reason 2: the shock wasn't held long enough

A single shock that fades back to normal chlorine within a day often leaves algae alive. The water then stays dull or cloudy, or drifts back toward green. TroubleFreePool's SLAM method (Shock Level And Maintain) treats algae by holding the shock level until all three of these are true:

  • combined chlorine is 0.5 ppm or less;
  • the overnight chlorine loss test shows 1 ppm of loss or less;
  • the water is crystal clear, with no visible algae, dead or alive.

Until then, test several times a day and top up whenever FC drops. For example, raising FC from 3 to 20 ppm in 10,000 gallons at 50 ppm CYA takes about 1.7 gal (6.4 L) of 10% liquid chlorine. With US household bleach at 6%, it's about 2.7 gal (10 L). Bleach is sold at 6% to 8.25%, so use the shock calculator with the percentage on your label. Follow the product label.

Pool School also says to adjust pH to 7.2–7.5 before you start, because the pH test isn't reliable during a SLAM. The full process is in green pool water: how to fix it, and how much shock to add to a pool covers each product type.

Reason 3: cal-hypo and calcium carbonate (milky white water)

If the water turned milky or white-blue right after shocking with granular cal-hypo (calcium hypochlorite), the haze may be calcium carbonate rather than dead algae.

  • Cal-hypo adds calcium along with chlorine. By Pool Calc's chemistry engine, 1 lb of 65% cal-hypo in 10,000 gallons adds about 7.8 ppm of free chlorine and about 5.5 ppm of calcium hardness. TroubleFreePool's Pool School notes that it raises calcium hardness with continued use and can cloud the water when alkalinity is high.
  • Taylor Technologies explains that water on the scaling side forms suspended calcium carbonate particles, and that rebalancing lets it dissolve back into the water.

What to do:

  1. Check your balance with the CSI calculator. A clearly positive CSI points to scaling.
  2. Bring pH down toward 7.2–7.4 and lower alkalinity if it's high. See pool alkalinity too high. We don't give a fixed acid dose for pH, because it depends on your alkalinity and other factors; the pH calculator works it out for your water.
  3. Keep filtering. The haze usually clears as the balance comes back.
  4. Next time, pre-dissolve. One EPA-registered cal-hypo label says to pre-dissolve the product in a clean plastic bucket of water before adding it to the pool, to add the product to water and never water to the product, and to mix it only with water.

If calcium hardness is already high, a liquid chlorine shock adds no calcium.

Reason 4: the filter isn't keeping up

Chemistry can be right while the filter falls behind. Taylor Technologies lists poor filtration and circulation as a main cause of cloudy water, and notes that backwashing sand and DE filters is important for clarity.

  • Pressure high? Clean the cartridge or backwash.
  • Pressure low or not changing? Check for a clogged skimmer or pump basket, or a valve in the wrong position.
  • DE filter putting white dust back into the pool? A torn grid can do that.
  • Short pump schedule? Run the pump continuously until the water is clear.

Clarifier or floc after shocking?

Clarifiers gather fine particles so the filter can catch them. Taylor Technologies notes that a clarifier can improve clarity for a while but is not a long-term solution. A flocculant is a different product type with different directions. If you use either, follow the product label exactly, and keep holding the shock level if you're still treating algae: a clarifier does nothing to living algae.

When can you swim?

Not while you can't see the bottom. The Washington State Department of Health's guidance for pool operators says that if you cannot see the bottom, you will not be able to see a person either, and that a pool should close when the bottom can't be clearly seen. Taylor Technologies gives the same advice: if you can't see the main drain, don't go in.

Once the water is clear: Swim when free chlorine is back within your normal range and at or below the re-entry level on your chlorine label (many labels say 4 ppm). Never swim during a SLAM or with free chlorine above 10 ppm. Your product label always comes first. If chlorine is still high after a shock, pool chlorine too high explains how to bring it down. For any question about your health, ask your doctor.

A quick diagnostic table

You see Most likely cause First move
Cloudy, a little clearer each day Filter removing dead algae Run the pump 24/7, brush, clean the filter
Cloudy, FC fell below the shock level Algae not finished Raise FC to the shock level and hold it
Milky white right after cal-hypo Calcium carbonate Check CSI, lower pH and alkalinity
No change for days, odd filter pressure Filter problem Clean, backwash or inspect the filter
Green tint returning Algae regrowing SLAM, see pool green but chlorine high

Common mistakes

  • Shocking once and stopping. If chlorine falls back before the three SLAM checks pass, the cloudiness and the algae can come back.
  • Adding more shock to calcium haze. More cal-hypo adds more calcium. Check balance first.
  • Turning the pump off at night. Fine particles settle and come back up the next day.
  • Reaching for a clarifier first. It can help a filter, but it doesn't fix the cause.
  • Losing track of top-ups. Pool Calc keeps every reading and dose in one log, so you can see how much chlorine the pool used each day.

Track it in Pool Calc

Pool Calc sets the shock level for your CYA, works out each top-up for the product you use, shows CSI on every result and tells you when you've passed the combined chlorine and overnight-loss checks. Get Pool Calc for iPhone and log your next test.

One pool? Every feature, free. No account, no ads, and iCloud backup is included.

Sources

Safety

  • Keep chemicals out of reach of children and pets, and keep them out of the water until it is back in range.
  • Never mix chemicals. Never add acid and chlorine together: mixing them releases toxic chlorine gas.
  • Add chemicals to water, never water to chemicals.
  • Store chemicals sealed, cool and dry, apart from each other.
  • Read and follow the product label. It always comes first.

Questions

Why is my pool cloudy after shocking?

Usually for one of four reasons: the filter is still removing dead algae and debris, the shock level wasn't held long enough to finish off the algae, the shock was cal-hypo and calcium carbonate formed in water with high alkalinity and pH, or the filter isn't keeping up. Test free chlorine, CYA, pH, alkalinity and calcium hardness, and check the filter pressure, to find out which one you have.

How long does a pool stay cloudy after shock?

It should look a little better each day. TroubleFreePool's Pool School notes that it can take the filter a week or more to fully clear the water after a SLAM, with sand filters the slowest. If you see no improvement at all from one day to the next, look at the filter and at whether the chlorine level is being held.

My pool is still cloudy 3 days after shocking. What should I do?

Test free chlorine and CYA. If free chlorine has dropped below the shock level for your CYA (for example 20 ppm at 50 ppm CYA), the algae may not be gone yet, so bring it back up and hold it. Run the pump around the clock, brush and vacuum daily, and clean or backwash the filter when its pressure rises about 25% over its clean reading.

Is it safe to swim in a cloudy pool after shock?

No. If you can't clearly see the bottom and the main drain, keep everyone out: the Washington State Department of Health puts it simply, if you cannot see the bottom you will not be able to see a person either. Wait until the water is clear and chlorine is back in range. Swim when free chlorine is back within your normal range and at or below the re-entry level on your chlorine label (many labels say 4 ppm). Never swim during a SLAM or with free chlorine above 10 ppm. Your product label always comes first.

Should I add a clarifier after shocking?

A clarifier can help a filter catch fine particles, but Taylor Technologies notes that clarifiers are not a long-term solution. Fix the cause first. If you use one, follow the product label and keep the filter running.