pH

How Much Soda Ash to Raise pH in a Pool

How much soda ash to raise pH in a pool depends on your alkalinity. See amounts for common pool sizes, how to add it, and when to skip soda ash.

Jump to the calculator

On this page
  1. Soda ash doses by pool size and alkalinity
  2. Why alkalinity changes the dose
  3. Should you use soda ash at all?
  4. How to add soda ash, step by step
  5. What to aim for
  6. Common mistakes
  7. Using soda ash in a hot tub
  8. Track it in Pool Calc
  9. Sources
  10. Safety

The quick answer: how much soda ash you need to raise pH depends on your pool's volume and its total alkalinity (TA). In 10,000 gallons with TA at 80 ppm, going from pH 7.2 to 7.6 takes about 16 oz (440 g). Test pH and TA first, enter them in the calculator, and follow the product label.

pH calculator

gal

Not sure? Work out your pool volume.

%
ppm

pH dosing depends on TA. Higher TA needs more acid.

ppm
ppm

Leave blank if you have never added borates.

°F

Add

15fl oz

of Muriatic acid 31.45%

1.9 cups448 mL

Lowers pH from 7.9 to 7.5 in 15,000 gal at TA 80. TA afterwards: about 76 ppm.

  • Side effects: TA −3.9 ppm.
  • Never add acid and chlorine together or in the same spot: mixing them releases toxic chlorine gas. Let the first one circulate before adding the other (the wait is shown on each step).
  • Pour it slowly in front of a return jet with the pump running.
  • Retest after the water has circulated.

Check the product label. Strengths vary by brand, so enter the % printed on yours. Add one chemical at a time, into the water, and never mix chemicals.

Save this test and get reminded when it is time to retest.

Download on the App Store

Soda ash doses by pool size and alkalinity

These amounts use plain soda ash (sodium carbonate) to take pH from 7.2 to 7.6, with no borates in the water:

Pool volume TA 60 ppm TA 80 ppm TA 100 ppm
5,000 gal (18,927 L) 5.8 oz (165 g) 7.8 oz (220 g) 9.7 oz (274 g)
10,000 gal (37,854 L) 12 oz (330 g) 16 oz (440 g) 1.2 lb (549 g)
20,000 gal (75,708 L) 1.5 lb (661 g) 1.9 lb (879 g) 2.4 lb (1.1 kg)

In metric, 10,000 litres at TA 80 ppm takes about 116 g for the same change.

Starting lower takes more. In 10,000 gallons at TA 80 ppm, pH 7.0 to 7.4 takes about 1.4 lb (651 g).

If your numbers aren't in the table, use the pH calculator. Don't scale a chart from another chemical, because baking soda, borax and soda ash all behave differently.

Why alkalinity changes the dose

TA is the water's buffer against pH change. The more buffer the water has, the more soda ash it takes to move pH the same distance. That is why a single "ounces per 10,000 gallons" figure can be well off for your pool.

Soda ash also adds TA with every dose. The Pool & Hot Tub Alliance's adjustment table lists 14 oz of sodium carbonate per 10,000 gallons for a 10 ppm rise in TA. Our engine gives 14 oz (401 g) for the same change. So raising pH this way also moves TA up, and it's worth retesting TA after each dose.

Should you use soda ash at all?

Check TA first, because it decides which product fits:

Your TA What to do Why
Low Soda ash, or baking soda if pH is close to target Soda ash raises both pH and TA. Baking soda mainly raises TA.
In range Soda ash or borax TroubleFreePool's Pool School notes that borax raises TA only a little
High Skip soda ash and aerate Aeration raises pH without raising TA, though it is slower

For the full picture on low readings, see pool pH too low. If TA is your main problem, go to pool alkalinity too low or pool alkalinity too high.

How to add soda ash, step by step

  1. Test pH and TA. A drop kit is the more accurate choice: CDC notes that test strips are less accurate.
  2. Work out the dose for your readings in the calculator, using your real volume. Set a target above your current pH and it switches from acids to pH increasers, including soda ash. If you aren't sure of it, see how many gallons is my pool.
  3. Follow the product label. Label directions come first if they differ from what is written here.
  4. Pre-dissolve it. Stir the soda ash into a bucket of water. Add the soda ash to the water, not the other way round.
  5. Pour slowly in front of a return jet with the pump running and nobody in the pool. Don't add it to the skimmer.
  6. Split larger doses. Indiana's state health guide suggests adding large amounts in thirds over about 2 hours.
  7. Circulate and retest. Wait at least 30 minutes, retest, and take the next reading before you add more.

Log each dose and result in Pool Calc for iPhone and it reminds you when to retest, so a second dose doesn't go in on top of one that hasn't settled.

What to aim for

Aim for about pH 7.4 to 7.6. PHTA's guideline lists 7.4–7.6 as ideal, with 7.2 as the minimum and 7.8 as the maximum. CDC recommends pH 7.0–7.8.

Since soda ash lifts pH and TA together, it also moves the water's calcium balance (CSI) upward. If your calcium or TA was already high, check the CSI calculator before a large dose.

If the pH drifts straight back up after your dose, the cause is usually high TA. See pool pH too high for what to do next.

Common mistakes

  • Using one figure for every pool. TA changes the dose, so test it first.
  • Adding soda ash when TA is already high. It lifts TA further, and pH tends to keep rising afterwards.
  • Treating baking soda as the same thing. It moves pH very little, so a baking soda dose won't do this job.
  • Skipping the metals check at very low TA. Indiana's guide says to test for metals before adding soda ash when TA is at or below 50 ppm.
  • Adding it all at once. Big jumps are harder to read and easier to overshoot. Split the dose.
  • Forgetting what went in. Pool Calc keeps every reading and dose in one log, so you can see how far each dose moved your water.

Using soda ash in a hot tub

Hot tubs hold far less water, so these amounts would be much too large. Use the Spa Calc guide to hot tub pH too low instead.

Track it in Pool Calc

Pool Calc works out the soda ash dose from your real TA and pool volume, splits large corrections, and charts pH over time. Get Pool Calc for iPhone and log your next test.

Sources

Safety

  • Keep chemicals out of reach of children and pets, and keep them out of the water until it is back in range.
  • Never mix chemicals. Never add acid and chlorine together: mixing them releases toxic chlorine gas.
  • Add chemicals to water, never water to chemicals.
  • Store chemicals sealed, cool and dry, apart from each other.
  • Read and follow the product label. It always comes first.

Questions

How much soda ash do I need to raise pH in a pool?

It depends on pool size, total alkalinity (TA) and how far pH has to move. In 10,000 gallons with TA at 80 ppm, going from pH 7.2 to 7.6 takes about 16 oz (440 g). Enter your own readings in the calculator, and follow the product label.

How much soda ash do I add to a 10,000 gallon pool?

About 12 oz (330 g) at TA 60 ppm, or 1.2 lb (549 g) at TA 100 ppm, to go from pH 7.2 to 7.6. Higher TA means more soda ash for the same pH change.

Does soda ash raise alkalinity too?

Yes. Soda ash raises both pH and TA. About 14 oz (401 g) adds 10 ppm of TA in 10,000 gallons. If TA is already high, aerate the water instead, because aeration raises pH without raising TA.

Is soda ash the same as pH increaser?

Many pool products sold as pH increaser or pH up are soda ash (sodium carbonate). Check the ingredient on your label. Baking soda is a different chemical: it mainly raises TA and moves pH very little.

How long after adding soda ash can you retest or swim?

Let the pump circulate the water for at least 30 minutes before you retest, and retest again after a few hours if the dose was large. Add it when nobody is in the pool, and follow your product label for when to swim.