Alkalinity

Pool Alkalinity Too Low: How to Fix It With Baking Soda

Pool alkalinity too low? What low TA does to pH, how much baking soda raises it 10 ppm, how to add it in steps, and what keeps pulling TA down.

Jump to the calculator

On this page
  1. What low alkalinity means
  2. What TA should you aim for?
  3. What pulls alkalinity down
  4. How to raise pool alkalinity, step by step
  5. What about pH?
  6. Plaster pools and CSI
  7. Common mistakes
  8. Track it in Pool Calc
  9. Sources
  10. Safety

The quick answer: when pool alkalinity is too low, raise it with baking soda (sodium bicarbonate, also sold as "alkalinity increaser"). Each 10 ppm of total alkalinity (TA) takes about 1.4 lb (635 g) per 10,000 gallons (168 g per 10,000 litres). Add it in steps, run the pump, and retest before the next step. Follow the product label.

The alkalinity calculator below works out the amount for your pool, your reading and your target.

Alkalinity calculator

gal

Not sure? Work out your pool volume.

ppm
ppm
%

Used to show the pH change.

Add

4.2lb

of Baking soda / alkalinity up (sodium bicarbonate)

67 oz1.9 kg

Raises total alkalinity from 60 ppm to 80 ppm in 15,000 gal. pH moves to about 7.6.

  • Side effects: pH +0.11.
  • Retest after the water has circulated.

Check the product label. Strengths vary by brand, so enter the % printed on yours. Add one chemical at a time, into the water, and never mix chemicals.

Save this test and get reminded when it is time to retest.

Download on the App Store

What low alkalinity means

Total alkalinity measures how well the water resists changes in pH. Taylor Technologies calls it the water's "buffering capacity". Most of it is bicarbonate, and it's reported in ppm.

When TA is low, the water has little buffer left. Small things then move pH a lot:

  • an acid dose for pH drops it further than you expected;
  • trichlor tablets pull it down;
  • a pH increaser sends it up too far.

TroubleFreePool's Pool School puts it plainly: with low TA, pH "tends to swing around wildly". That swinging is the main sign that TA is too low.

What TA should you aim for?

Sources give different ranges, because the right number depends on your pool:

  • TroubleFreePool's Pool School suggests 50 to 90 ppm, sometimes higher.
  • Taylor Technologies lists 60 ppm as a minimum and 80 to 120 ppm as ideal.

Both agree that below about 60 ppm is low for most pools. The pool alkalinity too high guide has a table of common targets by pool type. In short, salt water pools often run lower and pools on trichlor tablets often run higher.

Check for stabilizer in the reading. Cyanuric acid (CYA) adds to the TA test result. Taylor's correction is to subtract one-third of your CYA reading from the TA reading. At 60 ppm CYA, a TA reading of 70 ppm is really about 50 ppm of carbonate alkalinity.

What pulls alkalinity down

  • Acid. Every dose of muriatic acid or dry acid lowers TA as well as pH. Taylor notes that the same acid that lowers pH also lowers TA. Frequent acid doses add up.
  • Trichlor tablets. Trichlor is strongly acidic (its safety data sheet lists pH 3.0 for a 1% solution), so pools run on tablets lose TA steadily.
  • Low-alkalinity fill water. If your tap or well water is low in TA, top-ups and partial refills dilute it. Test your fill water once so you know.

If TA keeps dropping, find which of these is doing it. Otherwise you'll be adding baking soda every week.

How to raise pool alkalinity, step by step

  1. Test first. Test TA, pH, free chlorine and CYA. If TA reads high or low, test again before you add anything.
  2. Work out the dose. Use the calculator above, or the rule of thumb: about 1.4 lb of baking soda per 10 ppm per 10,000 gallons.
    • Example: a 10,000 gallon pool at 40 ppm, going to 70 ppm, needs about 4.2 lb in total.
    • Metric: 10,000 litres from 40 to 70 ppm needs about 504 g.
    • Larger pool: 20,000 gallons from 50 to 80 ppm needs about 8.4 lb.
  3. Add it in steps. For a rise of more than about 20 to 30 ppm, add half to two-thirds of the total first. Pool School suggests large increases be split into a few steps with a retest between them, because baking soda nudges pH up a little too.
  4. Spread it over the deep end with the pump running. Pool School's method is to spread it across the surface of the deep end. Brush any that settles on the floor so it dissolves. Follow the product label.
  5. Let it circulate, for a few hours at least, then retest TA and pH.
  6. Add the rest if TA is still short of your target.

Log each reading in Pool Calc for iPhone and it keeps the TA history next to your pH, so you can see whether the buffer is holding.

What about pH?

Baking soda raises pH only slightly. If pH is also low, you have two choices:

  • pH is just a little low: raise TA first, then retest pH. It may come up enough on its own.
  • pH is well below 7.0: soda ash raises pH and TA together, so it can fix both. Pool School notes that when TA is low, soda ash raises both. See pool pH too low, and use the pH calculator for the amount. The guide to how much soda ash to raise pH has examples by pool size.

CDC recommends keeping pool pH at 7.0 to 7.8 and notes that low pH can corrode pipes.

Plaster pools and CSI

In a plaster or pebble pool, low TA with low calcium hardness makes the water aggressive toward the surface. The Calcium Saturation Index (CSI) shows it as a negative number. After you raise TA, check the balance in the CSI calculator, and raise calcium too if it's low. Calcium hardness too low in pool shows how much calcium chloride to add and what level suits your surface. Vinyl and fiberglass pools are less sensitive to this, but pH still needs to stay in range.

Common mistakes

  • Using pH increaser to fix TA. Soda ash raises pH a lot more than baking soda does. If only TA is low, pH can overshoot.
  • Adding the whole amount at once for a big rise, then chasing high pH afterward.
  • Ignoring the CYA correction. With high CYA, TA can look fine on the test while carbonate alkalinity is actually low.
  • Treating the symptom only. If acid or tablets keep pulling TA down, it will come back. Note what you add.
  • Not writing doses down. Pool Calc logs each dose with its reading, so the next time TA drops you can see what changed.

Track it in Pool Calc

Pool Calc works out each baking soda step from your TA, target and pool volume, shows CSI with every result, and charts TA over time so you can spot a slow decline. Your custom TA target stays exactly where you set it. Get Pool Calc for iPhone and log your next test.

One pool? Every feature, free. No account, no ads, and iCloud backup is included.

Sources

Safety

  • Keep chemicals out of reach of children and pets, and keep them out of the water until it is back in range.
  • Never mix chemicals. Never add acid and chlorine together: mixing them releases toxic chlorine gas.
  • Add chemicals to water, never water to chemicals.
  • Store chemicals sealed, cool and dry, apart from each other.
  • Read and follow the product label. It always comes first.

Questions

How do I fix low alkalinity in my pool?

Add baking soda (sodium bicarbonate, sold as alkalinity increaser). It raises total alkalinity and nudges pH up only a little. Each 10 ppm takes about 1.4 lb (635 g) per 10,000 gallons. For a big rise, add it in two or three steps, run the pump, and retest between them. Follow the product label.

What are the symptoms of low alkalinity in a pool?

The main sign is pH that won't stay put: it drops or jumps after every chemical you add. TroubleFreePool's Pool School says that with low TA, pH tends to swing around wildly. In plaster pools, low alkalinity together with low calcium can push the water toward etching, which the CSI calculator shows as a negative number.

Can low alkalinity make a pool cloudy?

Cloudy water is usually a chlorine or filter problem, so test free chlorine against your CYA first and check the filter. Fix the alkalinity too, but don't expect baking soda to clear cloudy water on its own.

Should I use baking soda or soda ash to raise alkalinity?

Baking soda is the usual choice for raising TA, because it raises alkalinity with only a small rise in pH. Soda ash raises pH and TA together, so it suits a pool where both are low. If pH is fine and only TA is low, use baking soda.

How long after adding baking soda can I swim?

Follow the product label. Let the pump mix it in, then test pH and chlorine before anyone gets in. Swim when free chlorine is back within your normal range and at or below the re-entry level on your chlorine label (many labels say 4 ppm). Never swim during a SLAM or with free chlorine above 10 ppm. Your product label always comes first.