pH

Pool pH Too Low: What to Add and How to Raise It

Pool pH too low? What to add (soda ash, borax, baking soda or just aeration), how to choose by your alkalinity, and why pH keeps falling.

Jump to the calculator

On this page
  1. What counts as "too low"?
  2. Problems low pH causes
  3. Why pool pH drops
  4. What to add: pick by your alkalinity
  5. How to raise pH, step by step
  6. Low pH with high alkalinity: aerate
  7. How to keep pH from falling again
  8. Common mistakes
  9. Track it in Pool Calc
  10. Sources
  11. Safety

The quick answer: if your pool's pH reads below about 7.2, raise it back to about 7.4–7.6. What you add depends on your total alkalinity (TA): soda ash or borax when TA is normal or low, baking soda first when TA is low, and plain aeration when TA is high. The amount depends on your volume, TA and how far pH has to move, so use the calculator instead of a fixed chart, and follow the product label.

pH calculator

gal

Not sure? Work out your pool volume.

%
ppm

pH dosing depends on TA. Higher TA needs more acid.

ppm
ppm

Leave blank if you have never added borates.

°F

Add

15fl oz

of Muriatic acid 31.45%

1.9 cups448 mL

Lowers pH from 7.9 to 7.5 in 15,000 gal at TA 80. TA afterwards: about 76 ppm.

  • Side effects: TA −3.9 ppm.
  • Never add acid and chlorine together or in the same spot: mixing them releases toxic chlorine gas. Let the first one circulate before adding the other (the wait is shown on each step).
  • Pour it slowly in front of a return jet with the pump running.
  • Retest after the water has circulated.

Check the product label. Strengths vary by brand, so enter the % printed on yours. Add one chemical at a time, into the water, and never mix chemicals.

Save this test and get reminded when it is time to retest.

Download on the App Store

What counts as "too low"?

pH reading What it means
7.4–7.6 Ideal for most pools
7.2–7.8 Acceptable
7.0–7.2 Low. Raise it soon.
Below 7.0 Too low. Raise it before swimming. CDC recommends pH 7.0 to 7.8 for pools.
Below 6.5 The Model Aquatic Health Code calls this an imminent health hazard for public pools: immediate correction or closure.

Test with a drop kit if you can: CDC notes that test strips are less accurate.

Problems low pH causes

  • Corrosion. Low pH water is aggressive. CDC notes that pool pipes are more likely to corrode or break down when pH drops, especially below 7.0. TroubleFreePool notes that pH below 6.8 can damage metal parts, particularly heaters with copper heat exchangers.
  • Etched plaster and grout. Low pH pulls the water's calcium balance (CSI) negative, and water with a negative CSI dissolves calcium from plaster and grout. The CSI calculator shows where you stand, and calcium hardness too low in pool covers the calcium side.
  • Unstable readings. When pH is low because TA is also low, pH swings from day to day and any small acid dose moves it a lot.

Why pool pH drops

  1. Too much acid. A muriatic acid or dry acid dose that was too large for the pool's TA. A fixed chart is the usual cause, which is why acid doses should come from a calculator.
  2. Trichlor tablets. Trichlor is strongly acidic (its safety data sheet lists pH 3.0 for a 1% solution), so pools fed by tablets lose pH and TA week after week.
  3. Low total alkalinity. TA is the water's buffer. TroubleFreePool's Pool School puts it plainly: at low TA levels, pH tends to swing around.
  4. A reading error. Old reagents, strips left in a humid shed, or reading in poor light all give wrong colors. Retest before you add anything.

What to add: pick by your alkalinity

Test pH and TA first. TA decides which product fits.

Your TA What to add Why
Low (below your target) Baking soda first, then soda ash if pH is still low Baking soda raises TA with only a small pH change; soda ash raises both
Normal Soda ash (pH increaser) or borax Borax raises pH and adds just a little TA
High Nothing: aerate instead Aeration raises pH with no change in TA

For reference, about 1.4 lb (635 g) of baking soda raises TA by 10 ppm in 10,000 gallons (168 g per 10,000 litres). The pH dose for soda ash or borax depends on your TA, so it comes from the calculator, not a chart. For worked examples, see how much soda ash to raise pH. If TA is the main problem, see pool alkalinity too low.

How to raise pH, step by step

  1. Test pH and TA with a drop kit.
  2. Calculate the dose with the pH calculator, or the alkalinity calculator if TA is low. Enter the product you have.
  3. Follow the product label. Pre-dissolve granules in a bucket of pool water if the label says to.
  4. Add it slowly in front of a return jet with the pump running, spread around the pool.
  5. Large correction? Split it. Add part, circulate for at least 30 minutes, then retest before adding more.
  6. Keep chemicals apart. Don't add pH increaser and chlorine at the same time or in the same spot.
  7. Retest after a few hours of circulation and adjust.

Log each reading and dose in Pool Calc for iPhone, and it reminds you when to retest, so a second dose never goes in on top of a reading that hasn't settled.

Low pH with high alkalinity: aerate

This combination ("pool ph too low alkalinity too high") is common after an acid dose. Adding soda ash here would push TA even higher. Use air instead:

  • Point return jets up so they break the surface.
  • Run waterfalls, fountains, deck jets or a spillover spa.
  • Leave the pool uncovered while aerating.

As carbon dioxide leaves the water, pH rises without changing TA. It is slower than soda ash, often a day or more, but it is free. Once pH is back near 7.6 and TA is still high, the acid-and-aeration routine in pool alkalinity too high brings TA down step by step.

How to keep pH from falling again

  • Keep TA in range. TroubleFreePool's Pool School suggests about 50–90 ppm for most pools. Check your TA whenever pH starts to fall.
  • Watch tablet use. If trichlor is your daily chlorine, expect to add pH increaser or baking soda regularly, and keep an eye on stabilizer (CYA) building up. The FC/CYA chart shows how much chlorine your CYA level needs.
  • Use the calculator for every acid dose. Overshooting is the most common cause of low pH, and the opposite problem has its own guide: pool pH too high.
  • Test after heavy rain and after refilling.

Common mistakes

  • Using soda ash when TA is already high. It fixes pH today and makes it drift up faster next week.
  • Using baking soda to fix pH alone. It barely moves pH. It's the right product only when TA is low too.
  • Dumping in a full bag. Big jumps overshoot. Split the dose and retest.
  • Swimming at very low pH. Bring it back into range first.
  • Losing track of what went in. Pool Calc keeps every dose in a log, so you can see whether the drop came from tablets, rain or last week's acid.

Track it in Pool Calc

Pool Calc works out the soda ash, borax or baking soda dose from your real TA and pool volume, splits large corrections, and charts pH so you can see a downward drift before it becomes a problem. Get Pool Calc for iPhone and log your next test.

One pool? Every feature, free. No account, no ads, and iCloud backup is included.

Sources

Safety

  • Keep chemicals out of reach of children and pets, and keep them out of the water until it is back in range.
  • Never mix chemicals. Never add acid and chlorine together: mixing them releases toxic chlorine gas.
  • Add chemicals to water, never water to chemicals.
  • Store chemicals sealed, cool and dry, apart from each other.
  • Read and follow the product label. It always comes first.

Questions

What do I add if my pool pH is too low?

It depends on your total alkalinity (TA). If TA is low too, soda ash (pH increaser) raises both, or baking soda raises TA first. If TA is normal, soda ash or borax. If TA is high, aerate the water instead: it raises pH without raising TA. The calculator gives the amount for your pool, and the product label always comes first.

Can I use baking soda to raise pool pH?

Baking soda (sodium bicarbonate) mainly raises total alkalinity and lifts pH only a little. It is the right choice when TA is low as well. For reference, about 1.4 lb (635 g) raises TA by 10 ppm in 10,000 gallons.

What happens if pool pH is too low?

Low pH water is corrosive. CDC notes that pool pipes are more likely to corrode or break down when pH drops, especially below 7.0, and TroubleFreePool notes that pH below 6.8 can damage metal parts such as heater heat exchangers. CDC recommends keeping pool pH between 7.0 and 7.8.

My pool pH is low but alkalinity is high. What do I do?

Don't add soda ash, which raises TA further. Aerate the pool instead: point return jets up at the surface, run waterfalls or fountains, and retest. Carbon dioxide leaving the water raises pH with no change in TA.

Is it safe to swim when pool pH is very low?

The Model Aquatic Health Code treats a public pool below pH 6.5 as an imminent health hazard that needs immediate correction or closure. Raise pH to at least 7.0, and ideally 7.4 to 7.6, before swimming.