Edge of a pool with rippling teal water and warm stone coping in low golden sun

Chlorine

How to Read Pool Test Strips, and What to Do Next

How to read pool test strips: dip, hold the strip level, match each pad to the bottle's chart in daylight, then what each reading means and what to add.

Jump to the calculator

On this page
  1. How to read a pool test strip, step by step
  2. What each reading means, and what to do next
  3. Free chlorine or total chlorine?
  4. When a strip isn't enough
  5. Common mistakes
  6. Track it in Pool Calc
  7. Sources
  8. Safety

The quick answer: to read pool test strips, dip one strip as the bottle's directions say, hold it level without shaking off the water, wait the time printed on the bottle, then match each pad to the color chart on that same bottle in natural daylight. Then compare each reading with its range: CDC recommends a pH of 7.0 to 7.8 and at least 2 ppm of free chlorine in a pool with stabilizer, and at CYA 30 the engine behind Pool Calc sets the daily target at 5.3 ppm. Follow the product label for any chemical you add.

All-in-one pool calculator

gal

Not sure? Work out your pool volume.

ppm
ppm
ppm
ppm
ppm
°F
%
%

Two things to fix. Start with ph.

  1. pH 7.9 → 7.5

    Lower it

    Add

    15fl oz

    of Muriatic acid 31.45%

    1.9 cups449 mL

    • Side effects: TA −4 ppm.
    • Never add acid and chlorine together or in the same spot: mixing them releases toxic chlorine gas. Let the first one circulate before adding the other (the wait is shown on each step).

    Then wait 30 minutes with the pump running.

  2. Free chlorine 2 ppm → 6 ppm

    Raise it

    Add

    0.6gal

    of Liquid chlorine 10%

    77 fl oz2.3 L

    • Side effects: Salt +6.6 ppm.
    • Free chlorine is below the minimum for your stabilizer level.

In range

  • CH 300 ppm
  • CYA 40 ppm
  • TA 80 ppm

Water balance (CSI +0.32): Scale forming: calcium can come out as scale or cloudy water.

Check the product label. Strengths vary by brand, so enter the % printed on yours. Add one chemical at a time, into the water, and never mix chemicals.

Save this test and get reminded when it is time to retest.

Download on the App Store

How to read a pool test strip, step by step

Every brand of strip has its own pads, colors and timing, so the directions on your bottle come first. These steps are the parts nearly all of them share, taken from one strip maker's directions and Taylor Technologies' advice on testing.

Step 1: Take a strip with dry hands and close the bottle at once. Moisture and air wear the pads out. AquaChek's directions say to keep the cap closed tight between uses, store the bottle at room temperature, leave the drying packet inside, and not to use strips past the date on the bottle.

A plain container of test strips with two strips laid beside it on warm stone

Step 2: Dip it the way the bottle says. Taylor Technologies points out that some strips are meant to be dipped quickly, others swirled or swished, and that using the wrong motion spoils the colors. Take the water from about elbow depth, away from the return jets, and test right away. AquaChek's directions, for example, say to dip the strip and remove it at once.

Step 3: Hold it level and wait. Don't shake the water off. One maker's directions say to hold the strip level for 15 seconds before comparing; others use a different time, and Taylor warns that reading at the wrong time gives unreliable results. Use the time on your own bottle.

Step 4: Match the pads in daylight. Hold the strip next to the chart on the bottle, pad by pad, in the order the directions list them. Taylor recommends natural daylight and says to take sunglasses off, because tinted lenses and indoor light change how colors look. If a pad falls between two colors, note the value in between.

Step 5: Write the readings down. Log each one in Pool Calc for iPhone with the time, so the next test has something to compare with.

What each reading means, and what to do next

A strip gives you numbers; the next step is knowing which one to fix first. These ranges come from CDC, Taylor Technologies and TroubleFreePool's Pool School, and the chlorine levels from the same engine as Pool Calc.

Pad Aim for If it's off
Free chlorine At or above the minimum for your CYA (at CYA 30: 2.3 ppm), dosed up to the target (5.3 ppm) Add chlorine if low; let it fall if high
pH 7.0 to 7.8 (CDC) Acid lowers it; soda ash raises it
Total alkalinity 50 to 90 ppm (Pool School); 80 to 120 ppm (Taylor) Baking soda raises it; acid lowers it
Total hardness or calcium 250 to 650 ppm for plaster and fiberglass (Pool School); 200 to 400 ppm (Taylor) Calcium chloride raises it; replacing water lowers it
Stabilizer (CYA) Set by your chlorine type; see the FC/CYA chart Sets how much chlorine you need

Fix them in order. Taylor Technologies says to treat total alkalinity first, then pH, then calcium hardness, while you keep chlorine above the minimum for your stabilizer level the whole time. One chemical at a time, with the pump running.

Two glass test vials, one cloudy and one clear, beside a plain dropper bottle on stone

Low chlorine. For example, raising free chlorine from 2 to 5 ppm in a 10,000-gallon pool takes about 0.3 gal (1.1 L) of 10% liquid chlorine. US household bleach is sold at 6–8.25%, so use the chlorine calculator with the percentage on your own label instead of copying this example. Follow the product label. Pool chlorine levels has the full chart by CYA.

Low alkalinity. Raising TA from 60 to 80 ppm in 10,000 gallons takes about 2.8 lb (1.3 kg) of baking soda. Follow the product label.

High pH. The acid it takes depends on your alkalinity, so there is no fixed amount; use the pH calculator. Pool pH too high and pool pH too low cover both directions.

A closed, unlabeled jug with a teal cap on the stone edge of a pool

Free chlorine or total chlorine?

Many strips have two chlorine pads. The one you dose on is free chlorine. Total chlorine includes combined chlorine, which no longer sanitizes, so a total reading well above the free reading points to chloramines; free chlorine vs total chlorine explains the gap.

When a strip isn't enough

CDC says a DPD drop test kit gives the most accurate chlorine and pH results, and that test strips are less accurate. Strips are fine for a quick daily look. Use a drop kit when:

  • The chlorine pad reads zero but the water was just dosed. CDC notes that above 10 ppm a chlorine test can partly or fully bleach out and read falsely low or zero. Taylor's FAS-DPD drop test counts drops until the pink disappears instead of matching a color, so it reads free chlorine up to 20 ppm without bleaching out.
  • You're about to add a lot of something, such as a big chlorine dose or stabilizer, which is slow to remove once it's in.
  • Two strips from the same bottle disagree, or the colors land between steps on the chart.

Common mistakes

  • Using another brand's chart. Each maker's pads and colors differ. Taylor advises against mixing products from different makers.
  • Leaving the bottle open by the pool. Humid air spoils the strips in the bottle.
  • Reading too late. The colors keep changing after the read time.
  • Dosing on total chlorine. Dose on the free chlorine pad.
  • Testing once a week. CDC says to test chlorine and pH at least twice per day, and more often when a number of people are using the pool. Pool Calc keeps every reading and dose in one log, so a slow slide is easy to spot.

Track it in Pool Calc

Type your strip readings into Pool Calc and it tells you what to add, how much, and in what order, for the products you own. Get Pool Calc for iPhone and log your next test.

Sources

Safety

  • Keep chemicals out of reach of children and pets, and keep them out of the water until it is back in range.
  • Never mix chemicals. Never add acid and chlorine together: mixing them releases toxic chlorine gas.
  • Add chemicals to water, never water to chemicals.
  • Store chemicals sealed, cool and dry, apart from each other.
  • Read and follow the product label. It always comes first.

Questions

How do you read pool test strips?

Dip the strip as its directions say, hold it level without shaking off the water, wait the time printed on the bottle, then match each pad to the color chart on the bottle in natural daylight. One maker's directions say to dip and remove the strip at once, then hold it level for 15 seconds before comparing.

How long do you wait to read a pool test strip?

Use the wait time printed on your own bottle, because it differs between strips. Taylor Technologies warns that reading at the wrong time gives unreliable results. Read every pad within the window the directions give.

What should my pool test strip read?

CDC recommends a pH of 7.0 to 7.8 and at least 1 ppm of free chlorine, or at least 2 ppm when the pool uses cyanuric acid (stabilizer). In an outdoor pool the right chlorine level depends on your stabilizer: at CYA 30, keep free chlorine at or above 2.3 ppm and dose up to about 5.3 ppm.

Are pool test strips or drops better?

CDC says a DPD drop test kit gives the most accurate chlorine and pH results and that test strips are less accurate. Strips are quick for a daily check; confirm a reading that looks wrong, or one you are about to dose on, with a drop kit.

Why does my test strip show no chlorine?

Either the chlorine is low, or it is so high that the test bleached out. CDC notes that above 10 ppm a chlorine test can partly or fully bleach out and read falsely low or zero. If the water smells of chlorine or you just added a lot, retest with a kit that reads high levels before adding more.

Save this guide

How to Read Pool Test Strips, and What to Do Next: illustrated Pool Calc guide card

Download this guide as an image